30 Questions on Powder Coating Additives: From Leveling Agents to Texturing Agents, Answered in One Place (with a Dosage Table)

Oct 26,2026

Who this is for: powder coating manufacturers — new formulators, workshop technicians and purchasing engineers. Format: every answer runs in four lines — function → common types → dosage → cautions. Only categories and generic grades are listed; we do not rank specific suppliers. Dosage basis: publicly accepted industry ranges. Always confirm against your own resin system and acceptance criteria.


1. Film Formation and Appearance (Q1–Q5)

Q1. What does a leveling agent do, which types are common, and how much is used? It lowers and homogenises the surface tension of the film, removing craters and orange peel. Common types: acrylic homopolymers/copolymers, silicone-modified acrylates, polysiloxanes, and solid leveling agents . Dosage 0.8%–1.2% on binder, up to 1.5% with high oil-absorption pigments and fillers. Overdosing harms storage stability.

Q2. What does a gloss enhancer (brightener) do, and how much is used? It improves pigment and filler wetting and dispersion, assists leveling, reduces fine craters and raises gloss. Common type: butyl acrylate–methyl methacrylate copolymer , softening point 95–125°C. Dosage 1%–2% on binder. Overdosing reduces impact resistance and flexibility.

Q3. Must a leveling agent and a gloss enhancer always be used together? It depends on the leveling agent type. With an acrylic homopolymer leveling agent, a gloss enhancer is mandatory. With a copolymer multifunctional leveling agent, little or none is needed. Given the characteristics of domestic resin systems, the two are often required together to suppress fine craters.

Q4. What are the two matting routes? Physical matting (matting wax, acrylic resin / organic zinc salts): resists yellowing and costs less, but storage stability and resin selectivity are weaker. Chemical matting (B68-type chemical matting hardener based on cyclic amidine plus polybasic acid salt): strong matting power (gloss ≤10% is easy to reach), but prone to yellowing and higher in cost, and suitable only for epoxy-containing systems.

Q5. What is the mechanism and dosage of texturing agents? Physical type (amide-modified vinylidene fluoride polymers / polyolefins): raises viscosity and modifies surface tension so the melt forms a spiral and textures. Chemical type (metal-organic complexes): participates in the cure, shortens gel time, and the film textures because it has no time to level. Internal 3.5%–5% (on resin), post-add 0.2%–1.5% (on total formula). Higher dosage means coarser texture and lower gloss.

2. Bubbles and Defect Control (Q6–Q8)

Q6. What does a degassing agent do, and how much is used? It removes moisture adsorbed on pigments and fillers and the small molecules formed during cure, preventing pinholes and "pig pores". The most common are benzoin and silicone-modified benzoin. Dosage about 0.5% (on binder). HAA systems need <0.3% to avoid yellowing; benzoin has a large bake weight loss (about 25% in published research) and is one of the main sources of oven smoke.

Q7. When is a defoamer used? To eliminate bubbles and craters on porous substrates such as cast iron, cast aluminium and hot-rolled steel. Common types: glycol-treated carbonates, YPZ types. Dosage 0.5%–2% (on total formula). It cannot degas on its own; it is normally paired with benzoin.

Q8. How do you break through thick-film pinholes? Three moves together: control film build, optimise the degassing package (benzoin + defoamer, or modified benzoin), and where necessary use a low-viscosity wax to build vent channels (HAA cure generates water, so degassing has to be designed as a whole system).

3. Processing and Storage (Q9–Q11)

Q9. What does a dispersing agent do? It improves pigment and filler dispersion in the resin, develops colour and gloss, and lowers the shear load on the extruder. It usually works together with wetting promoters.

Q10. Are there internal and external anti-caking agents? Yes. Internal types (acrylic compounds) go through extrusion with the formula and work long-term; external types (fumed silica) are added before grinding and sieving and work immediately. Internal 0.3%–0.8%, external 0.1%–0.5%. Overdosing affects charging and leveling.

Q11. What does a dry-flow / antistatic additive solve? It lowers powder surface resistivity and improves dry-flow, preventing blockages in conveying and in the fluidised bed. Note that this is a different product from an antistatic agent used in the film — do not confuse the two.

4. Curing and Property Adjustment (Q12–Q15)

Q12. Which cure accelerators are available? Epoxy / epoxy-polyester: 2-methylimidazole, 2-phenylimidazoline, benzyltriethylammonium chloride. Polyester: quaternary ammonium bromides, triphenylphosphine. Polyurethane: dibutyltin dilaurate. Dosage from a few parts per ten thousand to a few parts per thousand. Overdosing shortens gel time too far and degrades leveling.

Q13. How do you toughen a coating or raise impact resistance? Full cure is the prerequisite. Then add plasticising additives to lower film stiffness, or use coupling agents to modify the filler and improve dispersion — better-dispersed filler gives higher impact at the same loading, and improves adhesion as a bonus.

Q14. When is an anti-sag agent used? To raise melt viscosity and build thixotropy, preventing sag on vertical surfaces and improving edge coverage. Common types: PVB, fumed silica, hydrogenated castor oil. Dosage 0.5%–2%. Use it together with the leveling agent to balance sag resistance against smoothness.

Q15. How should UV absorbers and light stabilisers be combined? For exterior formulations use a UV absorber (benzotriazole or triazine type) together with a hindered amine light stabiliser (HALS); either alone gives limited effect. Check compatibility with the resin and pigments and watch for migration.

5. Texture and Decorative Effects (Q16–Q19)

Q16. What is the mechanism and dosage of a wrinkle agent? It modifies the melt surface tension to form even wrinkles. Common types: CAB-based products and dedicated wrinkle additives. Dosage 0.5%–3%; more means a more pronounced wrinkle.

Q17. How is a "floating flower" agent used? It is dry-blended with a base powder that contains no leveling agent (no extrusion), and forms the pattern through a surface-tension differential. Dosage 0.05%–0.8% of the base powder. Clean the equipment thoroughly between colours to avoid cross-contamination.

Q18. What matters with hammer-tone agents? They work with non-leafing aluminium powder (1%–3%) to create the hammered effect. Dosage 0.1%–4.5%. Bake temperature must be uniform and the substrate must be flat.

Q19. How do you tune the gloss of a textured powder? Three levers: texturing agent dosage (primary), leveling agent dosage (raises gloss), and filler type and level (secondary). For reference, in an HAA system moving the texturing agent from 0.10% to 0.20% can take gloss from about 14% down to about 5% (published data).

6. Application Performance (Q20–Q23)

Q20. What does a charging enhancer solve? It raises powder charge and first-pass transfer efficiency and improves coverage on edges, corners and recessed Faraday-cage areas. Dosage 0.05%–0.4%. Overdosing causes powder agglomeration.

Q21. Who benefits from a tribo-charging additive? It improves the tribo-charging behaviour of polyester-epoxy and polyester powders for tribo guns. HAA systems contain nitrogen in their structure and charge naturally by friction, so they have an inherent advantage. Dosage about 1%–4%.

Q22. How many roles does wax play in a formulation? Six: scratch resistance (migrates to the surface and crystallises), slip, degassing (amide wax builds vent channels), matting, anti-caking, and carrier for bonded metallic powder. Waxes of different melting point and viscosity each have their own role — decide the role before choosing the wax.

Q23. How do you build a weathering package for exterior powder? Three lines of defence: rutile titanium dioxide + UV absorber + HALS. In dark systems, watch the bake weight loss caused by moisture adsorbed on carbon black.

7. Choosing the Cure System (Q24–Q27)

Q24. What are the key parameters of a TGIC system? CAS 2451-62-9, three epoxy functional groups. EEW about 100–110 g/eq, melting range about 90–110°C, polyester:TGIC ≈ 93:7 (by weight), cure 180–200°C × 10–15 min. Strong in mechanical properties, chemical resistance and thick-film behaviour; restricted by regulation in some markets, and handling requires ventilation and PPE.

Q25. What are the key parameters of an HAA system? N,N,N′,N′-tetrakis(2-hydroxyethyl)adipamide, MW 320.38, hydroxyl value 78–82 g/eq, melting range 125–130°C, volatiles ≤1.5%. Extrusion needs a slightly higher temperature (115–120°C) for dispersion; cure 180°C/15 min or 190°C/10–12 min. Low toxicity, fast cure, suited to tribo guns; cure releases water, so thick-film pinholing is its main weakness.

Q26. TGIC or HAA — who decides? Four hard constraints decide: the regulation in your destination market (for example the EU REACH classification of TGIC), whether the customer's specification mandates TGIC-free, the film thickness and pinhole requirements, and the tolerance for overbake yellowing. Regulations and specifications decide. Preference does not.

Q27. Can you switch systems (TGIC → HAA) by swapping the number? No. The polyester must change to an HAA-dedicated grade, the ratio must be recalculated from hydroxyl value, and degassing and extrusion temperature all have to be adjusted. Changing system is changing formulation, not changing a number.

8. Practical Miscellany (Q28–Q30)

Q28. How do you judge additive–resin compatibility quickly? Start with structural similarity, then check the carrier system (for example, an E-12-carried leveling agent must not go into a pure polyester system), then run a small plate trial. Amidine-containing chemical matting agents are restricted to epoxy systems — mismatch is an immediate failure.

Q29. Why must effect additives not be extruded with the base? Effect additives react prematurely in the extruder, and the film then shows no pattern or an uneven one. They must be post-added and dry-blended into the finished powder.

Q30. What is the first rule of formulation work? Change one variable at a time. Run control panels on the same resin lot and record batch drift. Any "add a bit more to be safe" move is the beginning of instability.


Appendix: Quick-Reference Dosage Table for 15 Additive Families (save this)

AdditiveCore functionTypical dosageKey warning
Leveling agentRemoves craters and orange peel0.8%–1.5% (on binder)Overdosing harms storage stability
Gloss enhancer (701 type)Raises gloss, suppresses fine craters1%–2%Overdosing lowers impact
Matting agentLowers glossPhysical type: by target glossChemical type: epoxy systems only
Texturing agentCreates textureInternal 3.5%–5% / post-add 0.2%–1.5%Dosage ↑ → coarser texture, lower gloss
Wrinkle agentCreates wrinkles0.5%–3%Balance against the leveling agent
Floating-flower agentCreates pattern0.05%–0.8% of base powderDry-blend post-add, do not extrude
Hammer-tone agentHammer finish0.1%–4.5%Match with 1%–3% aluminium powder
Degassing agent (benzoin)Prevents pinholesAbout 0.5%<0.3% in HAA systems
DefoamerPorous substrates0.5%–2%Pair with benzoin
Anti-caking agentPrevents cakingInternal 0.3%–0.8% / external 0.1%–0.5%Overdosing affects charging
Anti-sag agentPrevents sag0.5%–2%Balance against the leveling agent
Cure acceleratorAccelerates cureTens of ppm to a few per milleOverdosing degrades leveling
Charging enhancerRaises transfer efficiency0.05%–0.4%Overdosing causes agglomeration
Tribo-charging additiveTribo application1%–4%HAA systems have an inherent advantage
Antistatic agentFilm conductivity0.5%–3%Different product from dry-flow additive

How We Work with Powder Coating Plants: Our Customized Service

Fifteen additive families is a lot of variables to hold. We manufacture them, so we can consolidate them — and tune them — on your behalf.

1. One source, one specification file. Instead of buying fifteen additives from fifteen suppliers and reconciling fifteen data sheets, you can consolidate the families you use most onto one specification file with us: grade, active content, carrier, particle size, package. We produce against that file every time.

2. Grades adjusted to your resin, not to a catalogue. Leveling agent not compatible with your polyester? We change the carrier. Texture coarser than your gloss target allows? We change the particle-size band. Matting agent yellowing? We switch the route. Because the material is made in our plant, these are production decisions we make, not requests we forward.

3. Compatibility screening in our own laboratory. Send us your resin and we run the compatibility check — mini-extrusion, plate casting, gel time, gloss — before you order. We report what works and, just as usefully, what does not.

4. Pre-dispersed and blended packages. Where it helps your process, we supply combined packages (for example a degassing package balanced to a weight-loss ceiling, or a leveling plus gloss-enhancer pair pre-balanced for your resin) so you weigh one component instead of two.

5. In-house QC, retention samples, three-lot proof. Every lot is tested in our own laboratory and released against your specification; retention samples are kept. For any new grade we ship three consecutive lots with data attached before you scale.

6. Documentation and private label packing. TDS, SDS and COA issued by our own QC with every shipment; transport classification and UN information where applicable. Bags, labels and pallets can carry your brand.

Send us: your resin grades, the additive families you use, and the three defects you fight most often. We return: a consolidated specification, recommended grades and starting dosages, and trial samples. Price on request, per specification.


Online Message

* Note: Please be sure to fill in the information accurately and keep the communication unblocked, we will get in touch with you as soon as possible

%{tishi_zhanwei}%