TPEE vs TPU vs TPV: Which Elastomer Works Best for Automotive, Medical, and Industrial Applications?

Nov 09,2026

TPEE, TPU and TPV are the three thermoplastic elastomers most often specified for demanding B2B parts, and all three process like plastics while behaving like rubber. The short answer: TPEE fits high-temperature, oil-exposed dynamic parts; TPU fits abrasion-critical, tough, often transparent parts; TPV fits seals, outdoor parts and easy-to-recycle components. The right choice follows your performance priority — temperature, wear, sealing or weathering — not a brand name.

All three share thermoplastic processability (injection, extrusion, blow molding), recoverable elasticity, a broad hardness range and major weight savings over metal. They diverge sharply in molecular architecture, and that divergence drives every comparison below. 

Chemical Composition and Architecture

Material

Structure

Hard phase

Soft phase

TPEE

Linear block copolymer

Crystalline PBT polyester — strength, creep resistance, thermal stability

Aliphatic polyester or polyether — flexibility, rebound

TPU

Block copolymer from diol + diisocyanate + chain extender

Diisocyanate/chain extender — strength, rigidity, high melting point

Polyol (polyester or polyether type) — flexibility, low-temperature behavior

TPV

Dynamically vulcanized alloy

Crosslinked EPDM rubber particles (dispersed)

Polypropylene continuous phase

Key Distinction: TPEE is an engineering-grade polyester elastomer, TPU is a polyurethane whose properties depend heavily on polyol type, and TPV is a rubber-in-plastic alloy. This is why their "elasticity" feels and performs differently.

Mechanical Performance

Property

TPEE

TPU

TPV

Hardness range

Shore D32–D80 (~A70–D80)

Shore A10–D75

Shore A25–D54

Tensile strength

High; exceeds TPU at high temperature

30–65 MPa (ester > ether type)

Moderate; below TPEE and TPU

Elastic modulus

Very high, rigid at low strain

Moderate; rises with hard-segment content

Low to moderate

Abrasion resistance

Comparable to TPU

2–10× natural rubber

Good, generally below TPU

Compression set

Good among TPEs, poor vs. vulcanized rubber

Good to excellent

Superior; comparable to EPDM

Low-temperature impact

Excellent

High toughness

Good

Key Distinction: TPEE delivers far higher modulus and creep resistance, making it the choice for structural parts that must hold dimensions under sustained load. TPU wins on wear. TPV is the most rubber-like and best for compression-set-sensitive seals.

Thermal Performance

Property

TPEE

TPU

TPV

Continuous service temperature

–70 to 200 °C

–50 to 90 °C

–60 to 150 °C

Heat deflection

150–160 °C (paint-bake capable)

Limited above 90 °C

Good to 150 °C

Low-temperature flexibility

Brittle point below –70 °C

Good, varies with polyol

Flexible to –60 °C

Key Distinction: TPEE has the widest working window and the highest upper limit; TPU has the lowest ceiling; TPV sits in between. If the part sees 120 °C or a paint-bake cycle, TPEE is the only realistic option of the three. 

Chemical Resistance

Property

TPEE

TPU

TPV

Oil and grease

Outstanding, best of the three

Good to excellent (ester type better)

Comparable to chloroprene rubber

Fuel permeability

1/3 to 1/300 of conventional rubbers

Moderate

Moderate

Solvent resistance

Very good, low swelling

Moderate to good

Good

Hydrolysis resistance

Good

Ether type > ester type

Excellent

Acid / alkali

Good

Moderate

Good

Key Distinction: TPEE is the most resistant to oils, fuels and polar solvents; TPU performance swings with polyol type (better oil resistance but weaker hydrolysis for ester grades); TPV offers EPDM-like, balanced chemical resistance.

Weathering and Aging

Property

TPEE

TPU

TPV

UV resistance

Poor — needs stabilizers

Poor — degrades in sunlight

Excellent, EPDM-like

Ozone resistance

Good

Good

Excellent

Oxidation resistance

Good with stabilization

Requires stabilization

Excellent

Key Distinction: For outdoor parts, TPV is the default; both TPEE and TPU need UV stabilization, with TPU the most sunlight-sensitive

Processing and Recyclability

Property

TPEE

TPU

TPV

Melt stability

Excellent

Good

Excellent

Temperature sensitivity

Very high — small changes shift viscosity

Moderate

Low

Drying requirement

Required

Required

Minimal

Reprocessability

Fully recyclable

Fully recyclable

~6 cycles, minimal property loss

Key Distinction: TPEE demands the tightest temperature control and thorough drying; TPV is the easiest to process and most reprocess-stable.

Application Fit at a Glance

Application

Preferred

Why

CVJ boots, suspension, hydraulic hose covers

TPEE

Heat + fatigue + oil

Wheels, casters, transparent goods, overmolds

TPU

Abrasion + toughness

Seals, gaskets, weatherstrips, airbag covers

TPV

Compression set + weathering

Fuel lines, oilfield parts

TPEE

Low fuel permeability

Cable jackets and connectors

TPEE or TPU

Heat vs. abrasion priority

Soft-touch grips, consumer parts

TPV or SEBS-TPE

Cost and feel

How DOWREN Helps You Decide

Specifying an elastomer is rarely a one-table decision. DOWREN operates as an application technology center, not a volume-resin producer.

Grade matching and custom modification

We match grades to duty cycles and modify compounds — color, hardness, reinforcement and flame retardancy — through custom compounding.

Sampling and traceability

We run small-batch trials, supply batch-level COA and lot traceability, and ship globally. Send us your temperature profile, fluid list and cycle count, and our engineers will shortlist a grade and arrange a sample. 

FAQ

1. Which is better for high heat — TPEE or TPV?

TPEE. Its continuous range reaches 200 °C with 150–160 °C paint-bake tolerance, versus 150 °C for TPV and 90 °C for TPU.

2. Which elastomer resists oil and fuel best?

TPEE, with fuel permeability reported at 1/3 to 1/300 of conventional rubber. TPU is second and depends on polyol type; TPV is moderate.

3. Is TPV better for outdoor sealing?

Yes. TPV's EPDM-like UV and ozone resistance needs no additive package, and its compression set is superior to TPEE.

4. Can TPEE and TPU be recycled?

Both are fully recyclable; TPV tolerates about six reprocessing cycles with minimal property loss.

5. What is the hardest of the three?

TPEE reaches about Shore D80; TPU up to D75; TPV up to D54.

Need a TPEE Supplier You Can Audit?

DOWREN — the new materials business unit of ICASON Group,We supply controlled-compounded TPEE with batch-level traceability and a COA on every lot — custom hardness, color and modification available. No claims we cannot document. Contact us: Website: www.dowren.com · Phone / WhatsApp / WeChat: +86 16639328358

Online Message

* Note: Please be sure to fill in the information accurately and keep the communication unblocked, we will get in touch with you as soon as possible

%{tishi_zhanwei}%